One potential issue is the frequent use of lead-acid batteries for uninterruptible power supply systems (UPS), which can bridge the gap between grid outages and back-up generators. This is not necessarily an issue in itself, with much higher recyclability rates than lithium-based options, but other issues do crop up.
“Lead-acid batteries need to be replaced every three to five years – which, first of all, is not capex [capital expenditure] friendly and, second of all, for sure it’s not environmentally friendly,” says Henning Rath, CEO of EnerVenue. “That is something we are focusing on.”
The Californian battery company aims to address that issue with its Aqueous Metal Cell (AMC), a lithium-free, nickel-hydrogen battery for stationary storage. With a 30-year design life, the technology was adopted from NASA batteries first used to reliably provide decades of power to the Hubble Space Telescope and International Space Station.
EnerVenue “incubated” the technology at Stanford University, Rath tells Professional Engineering: “We reinvented the battery, we reinvented the electrodes, the electrochemistry, reduced the cost substantially, and the outcome is the Aqueous Metal Cell.”
The AMC contains a nickel hydroxide cathode and a nickel alloy anode in an alkaline water-based electrolyte. On charge, hydrogen gas is produced and stored inside a sealed, large-format cell. On discharge, the hydrogen reaction is reversed. The system is hermetically sealed to prevent leaks.
The cell’s features provide three main characteristics, according to Rath. “It has roughly 30,000 cycles, so an extremely long lifecycle. We can provide customers with a battery that needs no maintenance, or close to no maintenance,” he says.
“We cannot have a fire from thermal runaway – we have a water-based electrolyte. If the battery goes into thermal runaway or into distress, we basically vent water steam, which is obviously not flammable.
“And then the third one is we are not restricted to any supply chain, so our battery consists of nickel, steel, water and a little bit of glass fibre composite.”
That make-up is key to EnerVenue’s ambition to be a “global company”, with R&D teams in the US and local production. The firm opened its first high-volume manufacturing plant in Changzhou, China, in September, aiming to produce 300 AMCs per day. The facility’s first phase could provide 250MWh of battery capacity each year, rising to 1GWh in 2027 and beyond in 2028. Every cell passes 41 quality checks across 11 test-and-measure stations before leaving the building, to verify weld integrity, leak tightness and performance.
While the cells are aimed at various applications, including storing renewable energy and shaping power demands for commercial industrial buildings, the firm is “doubling down” on data centre power, with projects already operating in the US, China, Australia and Europe, and more on the way. Cells are aimed at the primary power supply, making sure facilities get continuous supply regardless of their power source, as well as UPS.
Unusual new applications are “popping up on a weekly basis”, Rath says. “I just came out of a call with a customer in Canada that deploys our batteries in the basement of office towers, basically, where the government is not allowing any kind of chemistries that may catch fire… We can run up to 60ºC on the cell level, 45ºC on a container level. There are many use cases that are evolving as the technology gets more and more known.”
The current product is aimed at a “sweet spot” for all applications, but a high-power cell in development could enable fast discharge times of 15 minutes. One parameter that is not a top priority for EnerVenue is energy density, with no aspirations to power vehicles.
“We have a lower energy density compared to, let’s say, lithium-based chemistries – but that’s OK, because we are not playing in this market,” Rath says. “There’s a clear trade-off on energy density. We don’t see the metric as, let’s say, watt hours per kilogram; we see it more like megawatt hours per acre, and in those metrics we are quite competitive.”
The maturity of the technology is ready to scale up, Rath says, with projects already running for a year. The biggest challenge will be the “extremely competitive” industry. “We need to hit the cost curve now with high-volume manufacturing and bring the levelised cost of storage – which is a key metric for us – down as fast as possible.”
Want the best engineering stories delivered straight to your inbox? The Professional Engineering newsletter gives you vital updates on the most cutting-edge engineering and exciting new job opportunities. To sign up, click here.
Content published by Professional Engineering does not necessarily represent the views of the Institution of Mechanical Engineers.